产品概述：

顶旺大理石胶粘粉是一款专为大理石及其它天然石材设计的粉白色水泥基石材专用的胶粘剂。具有粘结性强，耐候性好，不渗色等特点。

适用范围：

●室内外墙地面用于铺贴吸水率较低的瓷砖和室内墙地面铺贴石材；

●可直接应用于混凝土、水泥抹面、混凝土板、抹灰砖面和水泥基防水涂层上；

●可用于短暂或长期浸水环境，如浴室，泳池等；

●可用于铺贴陶瓷砖，马赛克，釉面砖和天然石材。

表面处理：

●所有表面应坚实、干净、无空鼓、无油污、蜡渍、脱模剂和其他松动物；

●油漆过的表面应作粗凿，至少暴露80%的原表面；

●混凝土面完成后，应养护至少28天方可铺贴，新抹灰的表面应养护至少7天方可铺贴；

●旧混凝土和抹灰表面可使用工业洗涤剂或去油污剂清洁，然后用高压水龙头冲洗干净。其表面经晾晒干24小时后方可铺贴；

●对于底材疏松且吸水性强货表面浮尘难彻底清理的表面，可先刷上顶旺L-BOND界面处理剂；

●在吸水率大的底材或在高温、干燥的环境下，施工前先润湿基面至外干内湿状态；

●施工前清理干净石材背后的网格布。

施工工艺：

●将大理石胶粘粉导入清水中搅拌成膏状，注意要先加水后导入粉剂，搅拌时使用电动搅拌机；

●混合比例：粉剂20公斤/水4.4-4.8升；必要时可使用顶旺瓷砖胶伴侣（DL）代替清水，将DL用清水1:1稀释后，再按20kg粉剂：5.6L添加剂比例使用；

●水粉充分拌合，完全无生粉团为准，搅拌完毕后需静止放置约十分钟后略微搅拌一下才可使用，可增加粘结力。

推荐使用刮板法铺贴，具体方法如下：

●用齿型刮板将胶浆涂于工作面之上，使之均匀分布，并形成一条条齿状，每次涂布不要超过1㎡，然后在晾置时间内将瓷砖/石材揉压于上即可；

●选择齿型刮板大小应考虑工作面的平整度和瓷砖背面的凹凸程度；

●如瓷砖背面的沟隙较深或石材、瓷砖较大较重，则应进行双面涂胶，即在工作面和瓷砖背面同时涂上胶浆。

关于室内里面石材无钉粘贴：

1.立面石材无钉粘贴需用顶旺瓷砖胶伴侣（DL）代替清水与大理石胶粘粉混合，以增加胶浆的粘结力和立面负重能力；

2.无钉粘结一般适用于面积等于或者小于400mm×400mm，厚度等于或则小于20mm的石材。若石材厚度在18mm以下，其面积可相应放大；

3.面积与厚度超过上述的石材，或质量特异的石材，需要先做现场粘结试验，以确定其是否适宜采取无钉粘结。

注意事项：

●施工温度应为5-35℃；

●水粉比例可因底材、天气、施工条件等不同而做出适当调整，禁止掺加其他材料改变胶粘粉配比和性能；

●胶浆应根据天气条件控制在2-3小时内使用完毕；

●切记将已干结的胶浆拌水后再用；

●铺砖完成后，须待胶浆完全干固后（约2小时）才可进行下一步的填缝工序；

●瓷砖胶粘剂的括涂应均匀且满贴，粘结层的厚度约为所用齿型刮板齿距的一半高；

●对于低吸水率的瓷砖，需用顶旺瓷砖伴侣（DL）代替清水与大理石胶粘粉混合；

●对于金属马赛克或电镀类马赛克，可能会腐蚀马赛克表面，建议要做局部试验后才可使用。

参考用量：

顶旺大理石胶粘粉理论用量约为：8.0-12kg/㎡。具体情况视基面和石材而定。

保质期：

未开封产品在阴凉通风处存放，在正常贮存和运输条件下，产品的保质期为一年。

执行标准：

C1 JC/T547-2005《陶瓷墙地砖胶粘剂》

声明：

施工请按照说明书的指示进行，本公司不承担由于不正确使用引起的任何损失责任，有关问题请咨询当地经销点或本公司技术服务部。

DESCRIPTION

Dingwang Dribond Marble is a cement based,premium grade adhesive for ceramic tiles.  Dingwang Dribond Marble is a high quality thick or thin adhesive.

USES

●Dingwang Dribond Marble may be used as a water resistant tile adhesive for interior and exterior tiling of walls and floors.

●Dingwang Dribond Marble may be applied directly onto concrete, cement render concrete blockwork and rendered brickwork surfaces and certain waterproofing membranes.

●Dingwang Dribond Marble may be used in areas where intermittent or continuous dampness occurs, i.e, shower floors, swimming pools.

●Dingwang Dribond Marble may be used for fixing ceramic, mosaic, slate, terracotta, vitrified and quarry tiles, marble and natural stone.

SURFACE PREPARATION

●All surfaces must be structurally sound, dry, clean and free from movement, oil, grease, wax, curing compounds and other loose contaminating materisals.

●Painted surfaces must be stripped to expose at least 80% of the original substrate.

●Newly rendered surfaces must be allowed to cure for at least 7 days, New concrete must be allowed to cure for 28 days.

●Porous surfaces should be primend with Dingwang L-Bond Primerflex/Additive.

●Steel trowel finished surfaces must be acid etched, mechanically scrabbled or wire brushed prior to tiling.

●Old concrete and rendered surfaces must be thoroughly clean prior to tiling.

●Remove the gridding cloth at the back of stones before application.

APPLICATION

●Always add Dingwang Dribond Marble to liquid component, mixing continuously until a lump free, creamy consistency is achieved.

●The mixing ratio is 50kg of Dingwang Dribond Marble powder to approximately 4.4-4.8litres of liquid.

●Spread the adhesive onto the substrate using a 6mm×6mm notched trowel for walls, a 10mm×10mm-12mm×12mm notched trowel for floor tiles.

●Ensure that there are no voies under the tiles. For tiles with deep groves or ridges, the adhesive should be buttered noto the back of the tiles in addition to being trowelled onto the substrate.

Note: The adhesive coverage must be uniform and cover entire tile thoroughly. The bed thickness must be approximately half the height of the square notched trowel used.

COVERAGE

Coverage varies according to the site conditions and build-up required.

SHELFLIFE

Store in unopened bags in an elevated cool dry place. The shelf life is one year under normal storage and transportation condition.

PRODUCTION STANDARD AND QUALITY DEGREE

C1 JC/T547-2005 《Adhesives for ceramic wall and floor tiles》

DISCALAIMER

The use of this product is beyond the manufacturer's control, and liability is restricted to the replacement of materials proven faulty. The manufacturer is not responsible for any loss or damage arising from incorrect usage.

生产日期 PRODUCTION DATE

生产批号 BATCH NUMBER

详见包装侧面喷码 Get the details on the side of the bag