TTB Ⅰ型（强力型）

产品概述顶旺TTB瓷砖胶Ⅰ型是一种聚合物改性的水泥基瓷砖胶粘剂，其施工操作性能、粘结性能等较之传统的水泥砂浆大幅改善。

适用范围：

●可用于混凝土、抹灰、砖墙面上粘贴吸水率大于6%的普通瓷砖、陶瓷马赛克和小型天然石材；

●与顶旺瓷砖胶伴侣（DL）添加剂配合使用，可在有轻微震动的基面上铺贴瓷砖。

表面处理：

●  所有表面应坚实、干净、无空鼓、无油污、蜡渍、脱模剂和其他松动物；

●  油漆过的表面应作粗凿，至少报暴露80%的原表面；

●  新混凝土面完成后，应养护至少28天方可铺砖，新抹灰的表面应养护至少7天方可铺砖；

●  旧混凝土和抹灰表面可使用工业洗涤剂或去油污剂清洁，然后用高压水龙头冲洗干净。其表面经晾干24小时后方可铺砖；

●  对于底材疏松且吸水性强或表面浮尘难彻底清理的表面，可先涂上顶旺L-Bond界面处理剂；

●  在吸水率大的底材或在高温干燥的环境下，施工前先润湿基面至外干内湿状态。

施工工艺：

●  将粉料倒入清水中搅拌成膏状，注意要先加水再倒入粉料，搅拌时使用电动搅拌机；

●  混合比例为粉剂20公斤：水4.4-4.8升；必要时可使用顶旺瓷砖胶伴侣（DL）代替清水，将DL用清水1:1稀释后，再按20公斤粉剂：5.6升添加剂比例使用；●  水粉充分拌合，完全无生粉团为准，搅拌完毕后需禁止放置约十分钟后略微搅拌一下才可使用，可增加粘接力。

推荐使用刮板法，具体方法如下：

●  用齿型刮板将胶浆涂于工作面之上，使之均匀分布，并形成一条条齿状。每次涂布约

1平方米左右（视天气温度而定），然后在晾置时间内将瓷砖揉压于上即可；

●  选择齿型刮板大小应考虑工作面的平整度和瓷砖背面的凹凸程度；

●  如瓷砖背面的沟隙较深或石材、瓷砖较大较重，则应进行双面涂胶，即在工作面和瓷砖背面同时涂上胶浆。

注意事项：

●  施工温度为5-35℃；

●  水粉比例可因底材、天气、施工条件等不同而做出适当调整，禁止参加其他材料改变胶粘粉配比和性能；

●  在雨天施工时，一定要做好遮蔽防护措施，并且要确保在贴砖后的24小时内，施工区域不被雨水淋湿；

●  胶浆应根据天气条件控制在2-3小时内使用完毕；

●  切忌将干结的胶浆拌水后再用；

●  铺砖完后，须待胶浆完全干固后（约24小时）才可进行下一步的填缝工序；

●  瓷砖胶粘剂的括涂应均匀且填满，粘结层的厚度应约为所用齿型刮板齿距的一半高。

参考用量：

顶旺瓷砖胶TTBⅠ型的理论用量约为3.5-3.7kg/㎡。具体情况视基面和瓷砖而定。

保质期：

未开封产品在干燥、阴凉、通风处存放。在正常贮存和运输条件下，产品保质期为一年。

执行标准：

Q/DGJC 2-2015  《TTB胶粘剂》

声明：

施工请按照说明书的指示进行，本公司不承担由于不正确使用引起的任何损失责任。有关问题请咨询当地的经销网点货本公司技术部。

DESCRIPTION

An economic thick and thin bed cement based adhesive, ideal for fixing ceramic,quarry and most

monocotturra tiles,slate,marble and natural stone to interlor and exterior walls and floors.

USES

● TTB can be used to lay tiles noto the concrete, cement render, blockwork and rendered brickwork surfaces.

● TTB can be used on walls and floors in both interior and exterior application.

SURFACE PREPARATION

● All surfaces must be structurally sound,dry,clean and free from movement,oil,grease,wax,curing compounds and other losse contaminating maerials.

 Painted surfaces must be scabbled to expose at least 80% of the original substrate. 

● Very porous surfaces must be scabbled to expose at least 80% of the original substrate. New concreate must be allowed to allowed to cure for 28days. Newly rendered surfaces must be allowed to cure for at least 7 days.

● Steel trowel finished surfaces must be acid etched or wire brushed prior to tiling. For old concrete and rendered surfaces,a strong commercial grade detergent or degreaser must

 be used to clean.

● Then thoroughly remove detergent/degreaser with fresh water using a high puessure hose. All surface to be dry for at least 24 hours prior to tiling.

● Ensure all release agents are removed from concerte surfaces,especially tilt-up slabs. 

APPLICATION

● Always add TTB powder to liquid component,mixing continuously until a thick creamy consistency is achieved.

● The mixing ratio is 20kg of TTB powder to approximately 4-4.8 litres of liquid.

● Spread the abhesive onto the substrate using a 6mm×6mm notched trowel for walls,a 10mm×10mm - 12mm×12mm notched trwel for floor tiles.

● Ensure that there are no voids under the tiles.For tiles with deep grover or ridges ,the adhesive

    should be buttered onto the back of the tiles in the addition to being trowelled onto the 

substrate.

NOTE: The adhesive coverage must be uniform and cover the entire tile thoroughly. The bed 

Thickness must be approximately half the height of the square notched trowel used.

COVERAGE

Coverage varies according to the site conditions and build up required.

SHELF  LFIE

Store in unopened bags in an elevated cool dry place. The shelf life is one year under normal 

storage and transportation condition.

PRODUCT STANDARD AND QUALITY DEGREE

C1 

Q/DGJC 2-2015

DISCLAIMER

The use of this product is beyond the manufacturer’s control , and liability is restricted to the 

replacement of materials proven faulty. The manufacturer is not responsible for any loss or damage

arising from incorrect usage.

生产日期 PRODUCTION DATE

生产批号 BATCH NUMBER

详见包装侧面喷码

Get the details on the side of the bag